10 51 43 – Wire Mesh Storage Lockers

Master Format 1995 – 10510

Division 10 – Specialties

SecurityCaging.com offers a wide variety of wire mesh storage lockers that can improve the efficiency of storage areas, secure important assets, and minimize clutter. SecurityCaging.com also provides other secure storage solutions such as wire mesh partitions, security caging, mezzanines, and more. 

GENERAL

• SECTION INCLUDES
  • Wire mesh storage lockers
  • Solid sheet metal bulk storage lockers.
• RELATED SECTIONS
  • Section 09900 – Paints and Coatings:  Field paintings
• SUBMITTALS
  • Submit under provisions of Section 01300.
  • Product Data:  Manufacturer’s printed data on products to be furnished.
  • Shop Drawings:  Complete layout and fabrication drawings.
  • Samples:  Finish color samples for selection.
  • Keys:  Turn over keys for door locks to Owner at completion of project. 

PRODUCTS

• STORAGE LOCKERS
  • Storage Lockers:  Factory-assembled modular sized door and divider panels bolted together, complete with all components, accessories, hardware, and fasteners; interchangeable units that allow expansion without waste of components.
    • Style:  Single tier.
    • Style:  Double tier.
    • Style:  Single and double tier, in arrangement shown on drawings.
    •  Width:  36 inches (915 mm).
    • Width:  48 inches (1220 mm).
    •  Depth:  36 inches (915 mm).
    • Depth:  48 inches (1220 mm).
    • Depth:  60 inches (1524 mm).
    • Height:  90 inches (2286 mm).
    • Provide tops of same construction as panels.
    • Provide backs where lockers are not to be installed against a wall; 20 gauge galvanized steel sheet.
    • Provide formed steel sheet bottoms.
    • Finish:  Powder coat acrylic enamel, electric static sprayed enamel. 
    • Provide appropriate hardware for fastening panels together and anchoring in place.
  • Wire Mesh Panels:  Steel angle frames with wire mesh securely welded in place; factory drilled holes for fasteners.

• Wire Mesh:  10 gauge, 0.135 inch (3.5 mm) steel wire woven into 1 by 2 inch (25 by 50 mm) rectangular mesh.
• Door Frames:  1-1/4 by 1-1/4 by 1/8 inch (32 by 32 by 3 mm) hot rolled steel angle.
• Wall Frames:  1-1/4 by 1-1/4 by 1/8 inch (32 by 32 by 3 mm) hot rolled steel angle on three sides, 1/8 inch by 3 inch (3 mm by 76 mm), steel flat on fourth side.
• Single Tier Doors:  1/4 by 3/4 inch (6 by 19 mm) steel bar stiffener securely welded to frame behind mesh.
• Doors:  Factory pre-hung; 2-1/2 by 2-1/2 inch (63 by 63 mm) spun pin hinges, welded in place; door strike and padlock hasp.

• Solid Sheet Metal Panels:  Steel angle frames with sheet metal securely welded in place; factory drilled holes for fasteners
  • Sheet Metal: 16 gauge 0.0598 inch hot rolled sheet
  • Door Frames:  1-1/4 by 1-1/4 by 1/8 inch (32 by 32 by 3 mm) hot rolled steel angle.
  • Wall Frames:  1-1/4 by 1-1/4 by 1/8 inch (32 by 32 by 3 mm) hot rolled steel angle on three sides, 1/8 inch by 3 inch (3 mm by 76 mm), steel flat on fourth side.
  • Single Tier Doors:  1/4 by 3/4 inch (6 by 19 mm) steel bar stiffener securely welded to frame behind mesh
  • Doors:  Factory pre-hung; 2-1/2 by 2-1/2 inch (63 by 63 mm) spun pin hinges, welded in place; door strike and padlock hasp.
  • Optional Three Point Locking system.
• Dividers and Bottoms:  16 gauge galvanized steel sheet, formed to provide extra strength and rigidity.
  • Dividers:  Anchor to supports bolted to wall panels, at 45 inches (1143 mm) above floor.

EXECUTION

• INSTALLATION
  • Install in accordance with manufacturer’s instructions.
  •  Install plumb, level, and securely anchored to floor and to other structural members where indicated, shim where necessary.
  •  Adjust doors smooth, easy operation.